TOPIC: PC Bootup Issues

villar61 wrote:

mga sir ano po solustion pag shorted po ang unit... ano ano po dapat kung gawin....

paano mo nalamang shorted?

---

added more infos on the first post.

Bien wrote:

villar61 wrote:

mga sir ano po solustion pag shorted po ang unit... ano ano po dapat kung gawin....

paano mo nalamang shorted?

---

added more infos on the first post.

sir kc minsan may continues beep po na sounds...
minsan wala naman po, may power po lahat(imiikit mga fan)la display sa monitor...

pinalitan ko po ng maraming working na psu, memory, videocard...

sa tingin ko baka po shorted... ano po ba gagawin... sa prob. ko salamat po...

sakin naman, pag press ko ng power button, il have to wait 4 about 2-3 mins and then press ko restart button at don lang mag oon ung pc. Na try ko na rin na palitan ung power supply pro ganon pa din prob. duda ko motherboard my prob..

borjok536 wrote:

sakin naman, pag press ko ng power button, il have to wait 4 about 2-3 mins and then press ko restart button at don lang mag oon ung pc. Na try ko na rin na palitan ung power supply pro ganon pa din prob. duda ko motherboard my prob..

Have you tried shorting the power pins on the motheboard directly?
Ako naman naging problema ko yung ayaw kaagad mag switch on kahit nakakailang pindot na ako kaya ginawa ko ginamitan ko ng tester yung power switch mahina na yung flow ng current kaya pala antagal or ayaw mag ON so nilipat ko ngayon siya from power button to reset button ayun sandali lang ON kaagad pag press mo

Bien wrote:

So many threads about this topic, new ones are being created almost daily with the same issue. So i'm making this thread to point out solutions for various causes of this problem.

No Power
-bad power cord
-bad power outlet
-bad casing power switch (swap with reset button connector to test)

PC powers on, but no display
remove all modules (vga, modem, lan card, hdd, etc), leaving only the PSU, memory and cpu plugged in the board. don't add another module until the pc boots up smoothly, with the hdd added last. Clean all slots to be used with a short burst from a contact cleaner spray, and let dry for a minute or two.
-check monitor connections
-swap memory module with a known good one
-reset BIOS
-swap video card
-clean vga and memory slots with a contact cleaner
-defective or incompatible keyboard
-defective motherboard. (last resort, wash with Joy liquid soap and rinse well. roaches, lizards, and mice sometimes gets in and pee on the board causing short circuits)

PC powers on with display, but shuts down immediately
-shorted or stuck up Power or Restart button
-defective PSU
-for defective LCD users, system unit is on but monitor only turns off. have the LCD monitor inverter circuit checked.

PC powers on with display, goes to Windows logon, then hangs or restarts.
-defective memory
-defective hdd
-wrong or corrupted device driver
-corrupted system files (do a chkdsk on another pc, or boot up from OS cd installer and do an hdd and system error check). may have been causes by a virus, so have it scanned from the 2nd pc (be careful not to have the other pc infected also. take precautions).
-run "repair Windows" in Windows setup
-cpu may be overheating (check bios hardware monitor for cpu temp. if near or over 70C, check your heatsink mounting and apply new heatsink compound)
-defective PSU
-defective accessory module (lan card, video card, etc)
-check all cooling fans, including vga card. may need cleaning and oiling.

---

***Will add more info if needed. Decided to open up the thread na lang. Please try to post infos or questions only.

Remember: if it ain't broke, don't fix it!

try ko nga po yan suggestions nyo sir, kase yan ang problema ko sa pc ko,

ang isang unit di na gumagana ang power supply after ng brown out, ano po kaya possible na dahilan or naging epekto nung brown out kaya ayaw na mag on ng pc
the other one naman po, ni-reformat ko kase sobrang bagal mag start tapos malapit nang matapos ang istallation may lumitaw na error like sinasabi na if you first time na experience ganitong error blah blah... alisin daw recent azdded hardware or other pero wala naman ako added harware po... after po nung error na yun hang ahg pc hindi natuloy setup ng xp. what i did po resstart ko pc pro ayaw na mag on.. total wala pero gumagana ang fan pero walang loading nung bios.

please help me naman po mga sir mam!


salamat madami

Bien wrote:

So many threads about this topic, new ones are being created almost daily with the same issue. So i'm making this thread to point out solutions for various causes of this problem.

No Power
-bad power cord
-bad power outlet
-bad casing power switch (swap with reset button connector to test)

PC powers on, but no display
remove all modules (vga, modem, lan card, hdd, etc), leaving only the PSU, memory and cpu plugged in the board. don't add another module until the pc boots up smoothly, with the hdd added last. Clean all slots to be used with a short burst from a contact cleaner spray, and let dry for a minute or two.
-check monitor connections
-swap memory module with a known good one
-reset BIOS
-swap video card
-clean vga and memory slots with a contact cleaner
-defective or incompatible keyboard
-defective motherboard. (last resort, wash with Joy liquid soap and rinse well. roaches, lizards, and mice sometimes gets in and pee on the board causing short circuits)

PC powers on with display, but shuts down immediately
-shorted or stuck up Power or Restart button
-defective PSU
-for defective LCD users, system unit is on but monitor only turns off. have the LCD monitor inverter circuit checked.

PC powers on with display, goes to Windows logon, then hangs or restarts.
-defective memory
-defective hdd
-wrong or corrupted device driver
-corrupted system files (do a chkdsk on another pc, or boot up from OS cd installer and do an hdd and system error check). may have been causes by a virus, so have it scanned from the 2nd pc (be careful not to have the other pc infected also. take precautions).
-run "repair Windows" in Windows setup
-cpu may be overheating (check bios hardware monitor for cpu temp. if near or over 70C, check your heatsink mounting and apply new heatsink compound)
-defective PSU
-defective accessory module (lan card, video card, etc)
-check all cooling fans, including vga card. may need cleaning and oiling.

---

***Will add more info if needed. Decided to open up the thread na lang. Please try to post infos or questions only.

Remember: if it ain't broke, don't fix it!

try ko nga po yan suggestions nyo sir, kase yan ang problema ko sa pc ko,

ang isang unit di na gumagana ang power supply after ng brown out, ano po kaya possible na dahilan or naging epekto nung brown out kaya ayaw na mag on ng pc
the other one naman po, ni-reformat ko kase sobrang bagal mag start tapos malapit nang matapos ang istallation may lumitaw na error like sinasabi na if you first time na experience ganitong error blah blah... alisin daw recent azdded hardware or other pero wala naman ako added harware po... after po nung error na yun hang ahg pc hindi natuloy setup ng xp. what i did po resstart ko pc pro ayaw na mag on.. total wala pero gumagana ang fan pero walang loading nung bios.

please help me naman po mga sir mam!


salamat madami

Bien wrote:

So many threads about this topic, new ones are being created almost daily with the same issue. So i'm making this thread to point out solutions for various causes of this problem.

No Power
-bad power cord
-bad power outlet
-bad casing power switch (swap with reset button connector to test)

PC powers on, but no display
remove all modules (vga, modem, lan card, hdd, etc), leaving only the PSU, memory and cpu plugged in the board. don't add another module until the pc boots up smoothly, with the hdd added last. Clean all slots to be used with a short burst from a contact cleaner spray, and let dry for a minute or two.
-check monitor connections
-swap memory module with a known good one
-reset BIOS
-swap video card
-clean vga and memory slots with a contact cleaner
-defective or incompatible keyboard
-defective motherboard. (last resort, wash with Joy liquid soap and rinse well. roaches, lizards, and mice sometimes gets in and pee on the board causing short circuits)

PC powers on with display, but shuts down immediately
-shorted or stuck up Power or Restart button
-defective PSU
-for defective LCD users, system unit is on but monitor only turns off. have the LCD monitor inverter circuit checked.

PC powers on with display, goes to Windows logon, then hangs or restarts.
-defective memory
-defective hdd
-wrong or corrupted device driver
-corrupted system files (do a chkdsk on another pc, or boot up from OS cd installer and do an hdd and system error check). may have been causes by a virus, so have it scanned from the 2nd pc (be careful not to have the other pc infected also. take precautions).
-run "repair Windows" in Windows setup
-cpu may be overheating (check bios hardware monitor for cpu temp. if near or over 70C, check your heatsink mounting and apply new heatsink compound)
-defective PSU
-defective accessory module (lan card, video card, etc)
-check all cooling fans, including vga card. may need cleaning and oiling.

---

***Will add more info if needed. Decided to open up the thread na lang. Please try to post infos or questions only.

Remember: if it ain't broke, don't fix it!

try ko nga po yan suggestions nyo sir, kase yan ang problema ko sa pc ko,

ang isang unit di na gumagana ang power supply after ng brown out, ano po kaya possible na dahilan or naging epekto nung brown out kaya ayaw na mag on ng pc
the other one naman po, ni-reformat ko kase sobrang bagal mag start tapos malapit nang matapos ang istallation may lumitaw na error like sinasabi na if you first time na experience ganitong error blah blah... alisin daw recent azdded hardware or other pero wala naman ako added harware po... after po nung error na yun hang ahg pc hindi natuloy setup ng xp. what i did po resstart ko pc pro ayaw na mag on.. total wala pero gumagana ang fan pero walang loading nung bios.

please help me naman po mga sir mam!


salamat madami

Bien wrote:

So many threads about this topic, new ones are being created almost daily with the same issue. So i'm making this thread to point out solutions for various causes of this problem.

No Power
-bad power cord
-bad power outlet
-bad casing power switch (swap with reset button connector to test)

PC powers on, but no display
remove all modules (vga, modem, lan card, hdd, etc), leaving only the PSU, memory and cpu plugged in the board. don't add another module until the pc boots up smoothly, with the hdd added last. Clean all slots to be used with a short burst from a contact cleaner spray, and let dry for a minute or two.
-check monitor connections
-swap memory module with a known good one
-reset BIOS
-swap video card
-clean vga and memory slots with a contact cleaner
-defective or incompatible keyboard
-defective motherboard. (last resort, wash with Joy liquid soap and rinse well. roaches, lizards, and mice sometimes gets in and pee on the board causing short circuits)

PC powers on with display, but shuts down immediately
-shorted or stuck up Power or Restart button
-defective PSU
-for defective LCD users, system unit is on but monitor only turns off. have the LCD monitor inverter circuit checked.

PC powers on with display, goes to Windows logon, then hangs or restarts.
-defective memory
-defective hdd
-wrong or corrupted device driver
-corrupted system files (do a chkdsk on another pc, or boot up from OS cd installer and do an hdd and system error check). may have been causes by a virus, so have it scanned from the 2nd pc (be careful not to have the other pc infected also. take precautions).
-run "repair Windows" in Windows setup
-cpu may be overheating (check bios hardware monitor for cpu temp. if near or over 70C, check your heatsink mounting and apply new heatsink compound)
-defective PSU
-defective accessory module (lan card, video card, etc)
-check all cooling fans, including vga card. may need cleaning and oiling.

---

***Will add more info if needed. Decided to open up the thread na lang. Please try to post infos or questions only.

Remember: if it ain't broke, don't fix it!

try ko nga po yan suggestions nyo sir, kase yan ang problema ko sa pc ko,

ang isang unit di na gumagana ang power supply after ng brown out, ano po kaya possible na dahilan or naging epekto nung brown out kaya ayaw na mag on ng pc
the other one naman po, ni-reformat ko kase sobrang bagal mag start tapos malapit nang matapos ang istallation may lumitaw na error like sinasabi na if you first time na experience ganitong error blah blah... alisin daw recent azdded hardware or other pero wala naman ako added harware po... after po nung error na yun hang ahg pc hindi natuloy setup ng xp. what i did po resstart ko pc pro ayaw na mag on.. total wala pero gumagana ang fan pero walang loading nung bios.

please help me naman po mga sir mam!


salamat madami

pertikacute wrote:

try ko nga po yan suggestions nyo sir, kase yan ang problema ko sa pc ko,

ang isang unit di na gumagana ang power supply after ng brown out, ano po kaya possible na dahilan or naging epekto nung brown out kaya ayaw na mag on ng pc
the other one naman po, ni-reformat ko kase sobrang bagal mag start tapos malapit nang matapos ang istallation may lumitaw na error like sinasabi na if you first time na experience ganitong error blah blah... alisin daw recent azdded hardware or other pero wala naman ako added harware po... after po nung error na yun hang ahg pc hindi natuloy setup ng xp. what i did po resstart ko pc pro ayaw na mag on.. total wala pero gumagana ang fan pero walang loading nung bios.

please help me naman po mga sir mam!


salamat madami

minsan nagha-hang mobo pag saglit lang brownout. yung tipong, pumitik lang kuryente. unplug the power cord, wait about 1-2 minutes (to give time for the capacitors to discharge), then replug. try powering up.

for the other issue, most likely, a memory problem. swap mo memory sa gumagana ng maayos. pag ganun pa din, it could be the mobo. i actually have 3 right now with the same problem. ok sa setup, pero pag restart, BSOD na.

try mo walang nakakabit na video card. built-in muna ikabit monitor. see if the problem goes away. pag ganun pa din, mobo na. pwedeng sira ang mga hardisk ports. (work around): use a pci hardisk adaptor.

sir Bien, ano po ang BSOD?

ayaw po talaga mag switch on kahit tanggal ko na ang VC palit ng iba kase wala syang built in VC eh, inalis ko then balik din agad ang cmos clock pero ayaw din,

pag switch on ko ang PC gumagana ang cpu fan pero walang nalabas kahit ano sa screen kahit yung LED indicator ayaw gumana, parang ayaw mag load ng bios.

salamat po!